Welcome to the A10 Networks Community! For any questions or concerns, please reach out to our admins.
A10 Community Forum
Welcome to the A10 Networks Community, a discussion forum where you can ask questions & interact with A10 customers.
Discussion List
- Hello! I would like to request your help, I have a thunder which is performing the nhld function with two ISPs and 3 published sites, internet browsing and published sites work correctly, but there is…
- Hi All, I am trying to write an additional policy based on the default url whitelist in the WAF templates. However the whitelist keeps failing the check due to a syntax error, but I can not see where …
- Hi Gurus, I'm testing a configuration with bridge-vlan-group and got the following Warning in the log: Mar 25 2015 14:05:57 Warning [ACOS]:<TEST> Potential loop detected on Port 3 VLAN 709 Src MAC 001…
- Hello, Maybe some of you have already faced this situation. On a box, the LSN and port distribution were configured for dynamic allocation with port-batch-v2, and the operation occurs as it should. Ho…
- Hi All, We have A10 TH3430S in HA setup , we are planning to migrate to Vthunder. Current setup have multiple partitions(L3V) having more than 30 nos VLAN through trunk. Even some partition have more …
- Hello! I have AX3000 loadbalancer and my desire is to use it as loadbalancer for my kubernetes cluster. I have three control planes nodes on kubernetes, with three different IP addresses, all of them …
- I recently upgraded a Thunder 1040 from 4.1.4 to 6.0.3. We use it for CGN. Afterwards we got a few complaints about VPN, SIP, and gaming losing connection. One complaint specifically mentioned the iss…
- Hello community, I have a connectivity issue about some users trying to get some social media pages, I have A10 thunder working as a CGNAT and I don´t have any rules filtering traffic. Waht could be t…
- Has anyone faced this problem so far? Аfter I log in, after a while the TPS Detector shows me this error.
- Howdy community, I have a cluster of A10 devices working with CGNAT, and also a Harmony Controller installed. I have changed the management ip in some A10 devices. My question is: how can I change the…
- Hi, installed the A10 V6 software in the Vpshere. VCS issue: After new build on A10 6.0.3 P2 the default multicast IP address (VCS config) is 224.0.1.210 (on V5 its 224.0.0.210) . VCS multicast IP add…
- Hi guys, Why does the Kafka service starts **** in the A10 Thunder device? I am using A10 Thunder as a CGNAT I had users unable to access social media pages, so we had to divert traffic to another dev…
- Hi guys, I need to ask, if I clear the DDoS Entries in the A10 device, this is going to affect the production evironment? Thanks
- I have 2 A10 thunder device in active passive cluster mode. We have 2 partitioned each node. Today all 4 ports in both the nodes went down and up again, causing services to move from one node to anoth…
- Hi all, A10 doc specifies about the SCTP FW, that “out-of-state packets and packets that fail packet anomaly checks per RFC 4960 are dropped.” But does anybody knows if it also remediates the vulnerab…
- Hi community, How could I clean up the ip addresses from the nat-pool which are in blacklists? I have issues with some users who can not open an specific url when they connect from FTTH home connectio…
- Hi I wonder if it is possible to use an Aflex inside another Aflex, for example when HTTP_RESPONSE { if { [HTTP::status] == 404 } { Aflex "ERROR-404" } } is this possible? Regards
- How can I call an slb template persist cookie template as command in an HTTP event For example: when CLIENT_ACCEPTED { if { [IP::addr [IP::client_addr] equals 192.168.1.10] } { pool example_server_gro…
Hi all, I want to know is it possible to check if the slb virtual server is up or down via API ?
Hello, I need help timeouts. We have a https virtual server, when i see its configuration "with-default" i see it has default tcp profile attached to it. As far as i know default tcp profile has idle …
Can someone help me with this problem? Failed to push zone Vlada_vremen_1 configuration on devices. Error: Failed to configure zone on detector group: Failed to configure Zone Vlada_vremen_1 on detect…- I'm currently encountering an issue with Galaxy NetFlow where I'm unable to view the netflow data, despite having checked and confirmed that the configuration is correct. Could someone kindly assist m…
Hello guys, Please I need to know, while setting a limit ID >user-quota tcp 2000 reserve 10 this means that 2000 ports will be the limit fot the whole NAT-POOL? (/24 mask) or per end user. And how can…- Hello everyone, I'm unsure how to access the most recent version of the solution; currently, I'm on version 5.0.6.94. Could someone please clarify which version is the latest? Additionally, I'd apprec…
s.
Hello I am trying to configure an A10 with 2 Internet Links to do response with a backup ip when gateway health check fails so I followed Multiple Gateway Links Configuration in the A10-GSLB.pdf but i…