-
GSLB Site
Hi When the GSLB Gateway site fails, do the SIPs related to this site go down in the gslb zone?
-
GSLB Gateway transparent Health monitor validation
Hello How can I configure the A10 to validate the GSLB gateway using a Health check with transparent to 8.8.8.8? for example, like we do in slb server because by default GSLB gateway validation is an ICMP to the gateway IP but if the gateway is UP but does not have access to the Internet the A10 will not know so it will…
-
DNS Response as Authoritative from GSLB server mode A10
Hi I want to configure the a10 to response as Authoritative so when someones quieres a FQDN in the A10 as server mode they will get the Authority flag = 1 I attach some screenshoots from my lab As you can see in the second screenshot authority = 0 Thanks for the help!
-
GSLB ZONE AS A RECORD
Hello! I´m configuring GSLB with a challenge which is to answer the queries for example.com as A record. example.com -> x.x.x.x The thing is that when we configured GSLB we have to add the domain in the zone and then configure the services for example www.example.com Does someone know how can I do this?
-
Question - GSLB Initial Configuration
Hello all, I’m just a bit confused when it comes to configuring my new A10 vThunder ADC/SLB with GSLB. I have been attempting to configure it per A10’s documentation, Would someone be willing to explain it a bit more for how its done in the GUI? I have 4 vThunders (2 per data center) and so far has 1 partition not…
-
I have some doubts about the A10 GSLB configuration,
Good day,dear all. We encountered some difficulties in configuring GSLB.Some configurations are as follows: gslb zone sgss.com.cn policy policy-test service 80 www policy policy-test dns-a-record www-ctc static admin-ip 100 dns-a-record www-ctcv6 static admin-ip 100 dns-a-record www-cuc static admin-ip 100 service 80 sso…
-
nslookup shown request timed-out
Hi Friends, I've been recently deployed GSLB setup in both DC & DR and dns delegation is working fine with the health checks. But when I try to trace the sites which I'm hosting it will show time-out waiting response. Any thoughts what cause this?
-
Health check did not work in GSLB
I have three ISP line,ISP1,ISP2 and ISP3. We check the ISP's health status with ICMP protocol,when ISP1 down,how to know the status?When ISP1 down,If the health check monitor go out through ISP2 or ISP3?So A10 can't know the ISP1 down.The health check monitor did not work.
-
GSLB between two different HW/SW Models
Hello all, Is it possible to run GSLb between two different HW? and two different ACOS ?
-
GSLB Always returns all DNS records in service
Hi - Old F5 customer here making the switch over to A10 and I am finding either GSLB does not behave as I am accustomed to or I don't know what I am doing. Probably the latter. I have set up GSLB using sub zone delegation whereby we have a delegated subzone that forwards requests to my A10 devices. For example: CNAME…
-
GSLB Service Port
What is the significance of the GSLB service port? I have set up my service IP ports to match my SLB configuration. I understand that service IP ports are in place because they can be used for health checking. However, at the service level, it seems the port is kind of redundant and I have simply set up port 53 to match…
-
GSLB across AX3000 and TH3030S cluster
I have new hardware in a new data center. The AX3000-11 runs 2.7.x while the TH3030S will be running 4.1.0. Is GLSB able to work when the two clusters are on different (yet current) firmware?
-
Need deployment guide specific to DNS Proxy using GLSB
deployment guide specific to DNS Proxy using GLSB
-
GSLB - Authoritative
Does anyone here tried to setup a GSLB Server mode or domain mode?
-
GSLB Proxy | Inbound NHLD
Does anyone here tried to deployed GSLB proxy mode in NHDL setup?
-
GSLB Link
I have an HA pair of AX3030's at data center 1, and another pair at data center 2. We are looking to establish a GSLB link between the 2 pairs. Do I need to have a layer 2 connection for the GSLB pair?
-
Zone transfer \ AXFR
Hi all, I'm trying to configure the AX so that he will be the primary DNS for a DOMAIN, the Domain is configured and functional for single UDP type queries (single sub-domain query) but For some reason AXFR queries are being dropped. when capture the request on the 'Debug gslb' i get an error stating "wrong query type" Is…
-
Geo-Location db
I am looking to start using geo-location with our GSLB config. The pre-loaded IANA db doesn't seem very specific within a country - or maybe I'm just reading things wrong. A problem I also see with this is that our physically diverse locations both show under the same net range in ARIN; since iana doesn't I can't assign…
