Options

aVCS and floating IP'S

[Deleted User][Deleted User] ✭
edited July 2022 in System
Posted by kmcewen@a10networks.com

Can some one please explain the traffic flow through the VCS.

I am working on an op where I cannot use SNAT and therefore reliying on the floating IP which is the default gateway for the servers.

How do we ensure that the traffic flows back via the incomming blade?

Ta 

Ken

Comments

  • Options
    [Deleted User][Deleted User] ✭
    edited February 2014
    Posted by TODDH

    It is VRRP-E (Data Plane) that controls where the floating IP resides. So if you have assigned VRID-2 to a VIP. The blade that has VRID2 active will control the VIP and the Floating address assuring symmetric traffic flow.

    Hope this helps.

    -Todd-
  • Options
    [Deleted User][Deleted User] ✭
    edited February 2014
    Posted by ddesmidt

    VCS (Virtual Chassis System) provides the following benefits:
    . Centralized management
    . Automatic AX config sync


    VCS does not provide AX High-Availability.
    This is achieved by the "old-HA" (called HA) or the "new HA" (called VRRP from 2.6).


    So if you have 2 AXs in active/standby mode:
    . 2 AX in high-availability (via "old-HA" or "VRRP")
    . 1 unique HA group ("old-HA") or VRRP vrid ("new-HA") for all the VIPs with Floating IP1
    . AX1 is active for HA group1, so:
    - active for VIP1 using servers S1A+S1B without SNAT
    - active for VIP2 using servers S2A+S2B without SNAT
    . AX2 is standby for HA group1, so:
    - standby for VIP1 using servers S1A+S1B without SNAT
    - standby for VIP2 using servers S2A+S2B without SNAT

    Both VIP1+VIP2 traffic is processed by AX1.
    And the servers S1A+S1B+S2A+S2B default gateway has to be AX floating IP1 (active on AX1).


    Now if you have 2 AXs in active/standby mode:
    . 2 AX in high-availability (via "old-HA" or "VRRP")
    . 1 HA group ("old-HA") or VRRP vrid ("new-HA") for some VIPs with Floating IP1
    . 1 other HA group ("old-HA") or HA vrid ("VRRP") for some VIPs with Floating IP2
    . AX1 is active for HA group1 and standby for group2, so:
    - active for VIP1 using servers S1A+S1B without SNAT
    - standby for VIP2 using servers S2A+S2B without SNAT
    . AX2 is standby for HA group1 and active for group2, so:
    - standby for VIP1 using servers S1A+S1B without SNAT
    - active for VIP2 using servers S2A+S2B without SNAT

    VIP1 traffic is processed by AX1.
    The servers S1A+S1B default gateway has to be AX floating IP1 (active on AX1).
    VIP2 traffic is processed by AX2.
    The servers S2A+S2B default gateway has to be AX floating IP2 (active on AX2).

    Note: You can't have 1 VIP active on 2 different AXs. AX Active/Active deployment requires at least 2 VIPs.


    Dimitri
Sign In or Register to comment.